Gold steel mesh weaving machine manufacturers to introduce the mesh weaving machine maintenance


Some parts of the net braiding machine, such as the spindle bracket, the sliding base, etc., ensure the accurate distance between the sliding base and the lower spindle braiding line when checking and disassembling or replacing new parts and reassembling. It is recommended to place a slider and The spindle to run on the sliding turntable to prevent the lower spindle braiding line from being stuck or cut off by the slider when it is introduced into the knitted fabric from the swing rod.

For rough adjustment, place the spindle on the two adjacent outer hammer supports, use the swing rod to guide the braided wire into the braiding point, and then overlap. When the braided wire enters or leaves the cut of the sliding turntable track, the distance from the spindle to the edge of the sliding frame is approximately equal.

Adjustment of the distance may be achieved by shifting one or more gears in front of or behind the carriage.

If the correct adjustment distance cannot be reached by moving 1 tooth, loosen the 5 fixing screws of the ring gear and become oval when passing through the hole. Therefore, the sliding frame can be fine-tuned by moving the ring gear. Tighten the screws to adjust the position. Place the remaining sliding blocks evenly on the sliding ring guide rail. After installing a new swing rod, if the swing height of the braided wire is different, all the swing levers need to be adjusted to have the same stopping point.

Gold steel mesh weaving machine manufacturers: how to effectively deal with the maintenance of weaving machines

Nowadays, knitting machines are very successful in many places. They are usually used specifically for knitting methods such as clothing, ropes, elastic bands, etc., but the interesting thing is that during long-term use, they sometimes wear and break down, so they need to be carried out daily. Repair, you need to remember an important point.

Braiding machine maintenance refers to the removal of the parts of the machine part, sorting and cleaning, replacing the parts that are expected to be damaged before the next overhaul, and then installing and adjusting according to the repair requirements. The time is usually 24 after the normal operation of the braiding machine About months.

During the overhaul, all mechanical parts shall be disassembled and cleaned, and worn parts shall be repaired. After the parts exceeding the service life are removed, the installation and adjustment shall be carried out according to the requirements of the overhaul. The major repair is usually carried out about 96 months after the normal operation of the pellet machine.

In addition, the main objective of the inspection is to remove dust and flying flowers from all parts of the machine, clean the knitting machine parts, replace the damaged parts, make the knitting machine mainly cotton yarn run normally for about 6 months, and check the knitting parts of the machine.

Mainly chemical fiber line, it can be overhauled after 12 months of regular operation. The specific operations are as follows: remove the impeller, horse walking lock, tension spring, etc., clean the platform, bearings, etc., reinstall, and readjust to the normal operation of the horse walking lock (horse walking head, spool) to ensure the fabric quality.

Jin Gang Mesh Braiding Machine Factory has been introduced here today. Thank you for watching and let's see you in the next issue!


Recommended Reading


Introduction of Metal Wire Mesh Loom

The metal wire mesh loom makes our company's main product is also one of our company's best-selling products. There are different models according to the diameter of the wire and the size of the mesh. Light metal wire mesh weaving machine, suitable for metal wire mesh weaving industry, can prepare empty mesh, dense grain mesh and other non-metal mesh. Its preparation products are widely used in petroleum, chemical, machinery, aviation and other industries. At present, our company's ZWJ-1300D-type metal wire mesh machine, ZWJ-1300B-type metal wire mesh machine, ZWJ-1300B (hanging)-type metal wire mesh machine, ZWJ-1300A-type metal wire mesh machine, ZWJ-13


Automatic weaving machine how to install and maintain

Fully automatic weaving machine is a kind of large-scale industrial equipment, which needs regular maintenance to ensure the normal operation of the machine and help to extend the service life of the machine. The maintenance failure of the machine will affect the normal operation of the machine, the machine parts will be damaged, and the service life of the equipment will be affected over time.


Strengthening Personnel Management and Improving Overall Quality

Jinglian Machinery Company issued a preliminary plan in 2019 to strengthen labor discipline and on-site management, so that employees can develop a good working habit and create a good working environment. Since February this year, the plan has been officially implemented. Starting from labor discipline, gfd, site environment and living environment. Continuously strengthen daily inspections and impose corresponding penalties on those who do not comply with the management system. In a short period of one month, the whole factory area has taken on a new look. In the past, cigarette butts were everywhere. Now it is difficult to find one. The working environment of the workshop has changed more. The whole workshop is clearly planned. The materials and workpieces are placed in an integrated way. The clothing of employees is worn.


Various updates and improvements bring new features to Beijing Union

Since the beginning of 2019, Jinglian Machinery Manufacturing Co., Ltd. has continuously made various improvements within the company, and the factory regulations, labor discipline, gfd, work and production environment, staff catering and other aspects have grown. The standardized operation of the production workshop and the inspection and inspection of each process are even more strict and strict. At present, the internal quality inspection basically realizes no leakage, no loss and perfect and clear records.


Machining industry knowledge

In order to let customers know more about our company and the machinery manufacturing industry, I will give you a detailed introduction to our company's various production equipment and machinery manufacturing industry knowledge. Machine tool is a machine that processes metal blanks into machine parts. It is a machine that makes machines, so it is also called "working machine" or "machine tool". It is customary to refer to machine tools for short. There are many ways to process mechanical parts in modern machinery manufacturing: in addition to cutting, there are casting, forging, welding, stamping, extrusion, etc., but all parts with high precision requirements and surface roughness requirements are generally required to be cut on the machine tool.


Mechanical processing industry knowledge-boring machine

Today we introduce some historical stories about boring machines and some related knowledge. 1, the earliest boring machine designer-Da Vinci boring machine is called "the mother of machinery". Speaking of boring machine, we have to talk about Leonardo da Vinci first. This legendary figure may have been the first designer of a boring machine for metal processing. The boring machine he designed is powered by water or foot pedals. The boring tool rotates close to the workpiece, which is fixed on a moving table driven by a crane. In 1540, another painter drew a picture of "fire engineering" with the same boring machine. At that time, the boring machine was specially used for fine addition of hollow castings.

Jinglian Machinery Manufacturing Co., Ltd.


Send mail

24-hour product hotline

Telephone/Fax:0318-7461330 

business negotiation

Mobile:18031805333

Production Park

Raoyang County Wugong Town Industrial Development Zone

Feedback

Our technicians will contact you within 12 hours and provide free plans and quotations.

Copyright©2023 Jinglian Machinery Manufacturing Co., Ltd.