How many steps are there in the hardware processing operation


I think we are not familiar with the word hardware manufacturing technology, but hardware products can be seen everywhere in our lives. Let's learn how many steps there are to pay attention to the hardware processing operation!

All employees of the 1. should check whether their clothes meet the work requirements before entering the work. Do not wear slippers, high heels or safety-affecting clothing. People with long hair please wear a helmet. We should work with a correct attitude and treat our work with full spirit. As soon as we find that we are not feeling well, we should leave our posts and report to our leaders. The operation must be considered intensively. It is strictly forbidden to chat and cooperate with each other. The operator should not operate in a state of irritability and fatigue to avoid accidents and ensure safe operation.

Before 2. the machine to work, check whether the moving part is supplemented with lubricating oil, and then start the clutch and brake to see if it is normal. The machine is idling for 1-3 minutes. It is strictly forbidden to operate when the machine fails.

When the 3. replaces the mold, cut off the power supply first, and wait for the press movement department to stop before starting the mold installation and adjustment. After installation and adjustment, try to hit the flywheel twice by hand to check whether the upper and lower molds are symmetrical and reasonable, whether the screws are firm, and whether the rim is in a reasonable position.

4. all other personnel leave the mechanical workshop and clean up the garbage on the workbench before starting the machine.

After the machine is 5. to work, no one is allowed to carry materials, operate the machine, and no other person is allowed to use electrical equipment or step on the foot switch board, reach into the working area of the machine, or touch the moving parts of the machine. Do not enter the sliding work area during mechanical operation. In addition, it is strictly forbidden to hold or place the workpiece by hand. When entering and exiting the workpiece in the mold, use a tool that meets the benchmark. When the machine makes an abnormal sound or the machine fails, please turn off the power switch immediately for inspection.

When the 6. is off work, turn off the power to ensure that the finished products, leftoving materials and garbage of the workshop are summarized to ensure the cleanliness and safety of the working environment.

The above operating procedures should be consciously observed. Operation must not be violated or malfunctioned. Cooperate with maintenance personnel to check, immediately cut off the power supply when an accident occurs, and maintain the on-site report to the factory department for processing. All consequences caused by the violation of the operating procedures shall be borne by the party concerned.

What is the difference between metal processing and sheet metal processing?

1. hardware introduction hardware is gold, silver, copper, iron, tin five kinds of metal materials, hardware processing is the mother of industry, is the foundation of national defense. According to the nature and use of hardware, it should be divided into 8 categories: iron and steel materials, non-ferrous metal materials, mechanical parts, transmission equipment, auxiliary parts, workpieces, real estate hardware, family hardware, etc. The purpose and effect of each hardware accessory are different, and the hardware processing can be selected in detail according to their own needs.

2. sheet metal introduction and sheet metal refer to the skills of processing uniform thickness plates. There are substantial differences between sheet metal processing and hardware, mainly in production processes such as shear bending welding. The metal neighborhood contains sheet metal and various sheet metal.

3. what is sheet metal processing?

Sheet metal processing is a hub technology mastered by sheet metal technicians, and it is also an important process for sheet metal product forming. Sheet metal processing includes traditional methods and process parameters such as material shearing, blanking, bending and stamping, as well as the structure and process parameters of various cold-pressing dies, the working principles and operation methods of various equipment, including new stamping technologies and new processes. The sheet metal processing is called sheet metal processing.

The above introduction is how many steps to pay attention to hardware processing operation, if you need to know more, you can contact us at any time!

Recommended Reading


Introduction of Metal Wire Mesh Loom

The metal wire mesh loom makes our company's main product is also one of our company's best-selling products. There are different models according to the diameter of the wire and the size of the mesh. Light metal wire mesh weaving machine, suitable for metal wire mesh weaving industry, can prepare empty mesh, dense grain mesh and other non-metal mesh. Its preparation products are widely used in petroleum, chemical, machinery, aviation and other industries. At present, our company's ZWJ-1300D-type metal wire mesh machine, ZWJ-1300B-type metal wire mesh machine, ZWJ-1300B (hanging)-type metal wire mesh machine, ZWJ-1300A-type metal wire mesh machine, ZWJ-13


Automatic weaving machine how to install and maintain

Fully automatic weaving machine is a kind of large-scale industrial equipment, which needs regular maintenance to ensure the normal operation of the machine and help to extend the service life of the machine. The maintenance failure of the machine will affect the normal operation of the machine, the machine parts will be damaged, and the service life of the equipment will be affected over time.


Strengthening Personnel Management and Improving Overall Quality

Jinglian Machinery Company issued a preliminary plan in 2019 to strengthen labor discipline and on-site management, so that employees can develop a good working habit and create a good working environment. Since February this year, the plan has been officially implemented. Starting from labor discipline, gfd, site environment and living environment. Continuously strengthen daily inspections and impose corresponding penalties on those who do not comply with the management system. In a short period of one month, the whole factory area has taken on a new look. In the past, cigarette butts were everywhere. Now it is difficult to find one. The working environment of the workshop has changed more. The whole workshop is clearly planned. The materials and workpieces are placed in an integrated way. The clothing of employees is worn.


Various updates and improvements bring new features to Beijing Union

Since the beginning of 2019, Jinglian Machinery Manufacturing Co., Ltd. has continuously made various improvements within the company, and the factory regulations, labor discipline, gfd, work and production environment, staff catering and other aspects have grown. The standardized operation of the production workshop and the inspection and inspection of each process are even more strict and strict. At present, the internal quality inspection basically realizes no leakage, no loss and perfect and clear records.


Machining industry knowledge

In order to let customers know more about our company and the machinery manufacturing industry, I will give you a detailed introduction to our company's various production equipment and machinery manufacturing industry knowledge. Machine tool is a machine that processes metal blanks into machine parts. It is a machine that makes machines, so it is also called "working machine" or "machine tool". It is customary to refer to machine tools for short. There are many ways to process mechanical parts in modern machinery manufacturing: in addition to cutting, there are casting, forging, welding, stamping, extrusion, etc., but all parts with high precision requirements and surface roughness requirements are generally required to be cut on the machine tool.


Mechanical processing industry knowledge-boring machine

Today we introduce some historical stories about boring machines and some related knowledge. 1, the earliest boring machine designer-Da Vinci boring machine is called "the mother of machinery". Speaking of boring machine, we have to talk about Leonardo da Vinci first. This legendary figure may have been the first designer of a boring machine for metal processing. The boring machine he designed is powered by water or foot pedals. The boring tool rotates close to the workpiece, which is fixed on a moving table driven by a crane. In 1540, another painter drew a picture of "fire engineering" with the same boring machine. At that time, the boring machine was specially used for fine addition of hollow castings.

Jinglian Machinery Manufacturing Co., Ltd.


Send mail

24-hour product hotline

Telephone/Fax:0318-7461330 

business negotiation

Mobile:18031805333

Production Park

Raoyang County Wugong Town Industrial Development Zone

Feedback

Our technicians will contact you within 12 hours and provide free plans and quotations.

Copyright©2023 Jinglian Machinery Manufacturing Co., Ltd.